CFI-I Dumps PDF 2025 Strategy Your Preparation Efficiently
Latest Verified & Correct NFPA CFI-I Questions
NEW QUESTION # 30
What is the maximum occupant load for a conference room with a total area of 900 ft² (84 m²)?
- A. 90 people
- B. 120 people
- C. 60 people
- D. 30 people
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Occupant Load Calculation:
According to NFPA 101 (Life Safety Code), Table 7.3.1.2, for assembly occupancies without fixed seating (such as conference rooms), the occupant load factor is:
15 ft² (1.4 m²) per person.
Calculation:
Divide the total area of 900 ft² by 15 ft per person: 900ft2/15ft2/person=60people900 \, \text{ft}^2 \, / \, 15 \, \text{ft}^2/\text{person} = 60 \, \text{people}900ft2/15ft2/person=60people Other Options Explained:
Option A (30 people): Too low.
Option C (90 people) and Option D (120 people): Exceed the calculated occupant load.
Summary:
The maximum occupant load for a 900 ft² conference room is 60 people.
NEW QUESTION # 31
Where is the evacuation and relocation plan maintained in existing health care occupancies?
- A. In the hospital administrator's office
- B. In the local fire department's dispatch center
- C. In the building manager's office
- D. In the facility's telephone operator's location or in the security center
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Evacuation and Relocation Plans:
According to NFPA 101 (Life Safety Code), Section 18.7.2.2, for existing health care occupancies, the evacuation and relocation plan must be readily accessible and maintained in a location where it can be quickly referenced during an emergency.
Specific Locations:
The facility's telephone operator's location or the security center is ideal because:
These areas are staffed continuously.
Personnel in these locations can coordinate emergency responses quickly.
Other Options Explained:
Option A (In the building manager's office): Typically not staffed 24/7, and the plan may not be accessible during an emergency.
Option B (Local fire department's dispatch center): While helpful, the plan must be maintained onsite for immediate use.
Option D (Hospital administrator's office): This location is less practical during emergencies.
Summary:
The evacuation and relocation plan in existing health care occupancies must be maintained in the facility's telephone operator's location or security center for quick access during emergencies.
NEW QUESTION # 32
New underground and limited access structures require an approved, supervised, automatic sprinkler system, when the occupant load meets or exceeds how many people?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Sprinkler System Requirement:
According to NFPA 101 (Life Safety Code), Section 11.8, new underground and limited-access structures with an occupant load of 20 or more people are required to have an approved, supervised automatic sprinkler system.
Why 20 People is the Threshold:
Underground and limited-access structures pose unique fire and life safety challenges due to restricted egress and ventilation.
Automatic sprinkler systems mitigate fire hazards by controlling or suppressing the fire, allowing time for evacuation.
Other Options Explained:
Option A (10 people): Not the specified threshold.
Option C (40 people) and Option D (50 people): Too high; NFPA sets the limit at 20 people for these structures.
Summary:
An automatic sprinkler system is required when the occupant load in new underground or limited-access structures meets or exceeds 20 people.
NEW QUESTION # 33
What class of organic peroxide burns rapidly and presents a moderate reactivity hazard?
- A. Class II
- B. Class IV
- C. Class I
- D. Class III
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Organic Peroxides:
Organic peroxides are highly reactive chemicals that can burn rapidly or decompose, presenting significant fire and explosion hazards.
They are classified into classes based on their burning rate and reactivity hazard according to NFPA 400 (Hazardous Materials Code).
Class II Organic Peroxides:
Class II organic peroxides are characterized by:
Burning rapidly.
Presenting a moderate reactivity hazard.
They are less hazardous than Class I but still require precautions during storage and handling.
Other Options Explained:
Option A (Class I): Extremely hazardous; burns rapidly with high reactivity.
Option C (Class III): Burns moderately and has a lower reactivity hazard.
Option D (Class IV): Burns slowly with minimal reactivity hazard.
Summary:
A Class II organic peroxide burns rapidly and presents a moderate reactivity hazard as defined by NFPA 400.
NEW QUESTION # 34
Where shall fire department connections on wet-pipe automatic sprinkler systems be located?
- A. On the system side of the water supply check valve
- B. On the suction side of booster pumps
- C. On the supply side of the check valve in a single-riser system
- D. Above the dry-pipe valve on a single-riser dry-pipe system
Answer: A
Explanation:
The placement of the fire department connection (FDC) for a wet-pipe automatic sprinkler system is governed by NFPA 13, Standard for the Installation of Sprinkler Systems.
The FDC must be located on the system side of the water supply check valve (A). This ensures that the fire department can pump water into the system effectively and directly supply the sprinkler system during an emergency.
Suction side of booster pumps (B): This placement would not supply water correctly to the system during firefighting operations.
Supply side of the check valve (C): This would prevent water from entering the sprinkler system since the check valve blocks backflow from the FDC.
Above the dry-pipe valve (D): This applies to dry-pipe systems, not wet-pipe systems.
Reference:
NFPA 13, Section 8.17.2.4: Location requirements for fire department connections.
NEW QUESTION # 35
Records regarding fire prevention inspections must include all of the following EXCEPT
- A. a summary of violations found during the inspection
- B. the date of the inspection
- C. dates of the service of notices
- D. photographs of code violations
Answer: D
Explanation:
Fire prevention inspection records must include essential details to ensure a proper record of the inspection process and enforcement of fire codes. According to NFPA 1, Fire Code, and standard fire inspection procedures:
Summary of violations found (A): This provides a clear record of noncompliance issues identified during the inspection.
Date of the inspection (B): The inspection date is mandatory for tracking inspection schedules and enforcement timelines.
Dates of the service of notices (C): These dates are necessary to document when violations were communicated to the responsible party.
Photographs of code violations (D): While photographs can be useful for documentation, they are not a mandatory requirement under NFPA standards for inspection records.
Reference:
NFPA 1, Fire Code, Chapter 1: Documentation requirements for fire inspection records.
NEW QUESTION # 36
What is the classification for an occupancy used to provide overnight treatment and observation for 5 to 10 bed-ridden persons that simultaneously renders the persons incapable of self-preservation under emergency conditions?
- A. Health care
- B. Residential board and care
- C. Ambulatory health care
- D. Limited care facility
Answer: D
Explanation:
The classification of occupancies for care facilities is defined in NFPA 101, Life Safety Code.
Limited care facility (B): This classification applies to facilities providing overnight care for 4 or more persons who are incapable of self-preservation but do not meet the requirements for a full health care occupancy.
Health care (A): Applies to hospitals and nursing homes where more intensive medical care is provided.
Residential board and care (C): Involves personal care but not medical treatment.
Ambulatory health care (D): For outpatient services where occupants are capable of self-preservation.
Reference:
NFPA 101, Section 3.3.49.4: Definitions for limited care facilities.
NEW QUESTION # 37
When conducting a main drain test of a water-based fire protection system riser, what percentage of reduction in full flow pressure (as compared to the acceptance test or previously performed test) will trigger an investigation into the cause of the reduction?
- A. 3 percent
- B. 10 percent
- C. 5 percent
- D. 2 percent
Answer: C
Explanation:
A main drain test ensures that water flow and pressure in the system remain consistent. According to NFPA 25, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems:
A 5 percent or greater reduction in full flow pressure compared to prior tests triggers an investigation to identify and correct potential issues (e.g., obstructions or valve malfunctions).
Reference:
NFPA 25, Section 13.2.5.2: Pressure reduction thresholds for main drain tests.
NEW QUESTION # 38
Smoking is prohibited within what minimum distance from an outdoor hazardous material storage facility or dispensing area?
- A. 100 ft (30.4 m)
- B. 25 ft (7.6 m)
- C. 10 ft (3.4 m)
- D. 50 ft (15.2 m)
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Smoking Prohibition Near Hazardous Materials:
According to NFPA 1 (Fire Code), Section 60.5.2.3, smoking is prohibited within a minimum of 50 feet (15.2 m) from outdoor hazardous material storage facilities or dispensing areas to reduce fire risks from ignition sources.
Why 50 Feet is Required:
Hazardous materials can release flammable vapors that ignite easily. The 50-foot distance ensures safety by minimizing the risk of exposure to open flames or sparks.
Other Options Explained:
Option A (10 ft) and Option B (25 ft): Too close to ensure safety.
Option D (100 ft): More than required under NFPA 1.
Summary:
Smoking is prohibited within 50 feet (15.2 m) of outdoor hazardous material storage or dispensing areas.
NEW QUESTION # 39
What is the maximum slope for a ramp in an existing business occupancy?
- A. 1 in 10
- B. 1 in 8
- C. 1 in 12
- D. 1 in 14
Answer: C
Explanation:
The maximum allowable slope for ramps in existing buildings, including business occupancies, is specified in NFPA 101, Life Safety Code.
1 in 12 (C) corresponds to a slope of 8.3% (1 unit of vertical rise for every 12 units of horizontal distance). This is the maximum allowable slope for ramps to ensure accessibility and safety for all occupants, including individuals with disabilities.
Steeper slopes, such as 1 in 8 or 1 in 10, exceed the limits and pose accessibility and usability issues.
1 in 14 (D) would be a gentler slope, but it is not required for existing occupancies.
Reference:
NFPA 101, Section 7.2.5.4: Ramp slope limitations for new and existing buildings.
ADA Guidelines: Also enforce a 1:12 slope for accessibility compliance.
NEW QUESTION # 40
Which of the following operations would NOT require a permit issued by the AHJ?
- A. The storage, use, and handling of flammable liquids
- B. The maintenance of fire protection systems
- C. The installation of an automatic fire suppression system
- D. The use of mall areas for exhibits or displays
Answer: B
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Permits and AHJ Oversight:
The Authority Having Jurisdiction (AHJ) issues permits for operations that:
Involve fire safety risks.
Impact public safety and property protection.
Require significant modifications, installations, or special activities.
Option A: Maintenance of Fire Protection Systems
Maintenance refers to routine tasks like inspections, testing, and minor repairs to keep fire protection systems functional.
NFPA 25 (Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems) does not require a permit for standard maintenance.
Maintenance ensures compliance but does not typically involve new installations, modifications, or hazardous conditions that warrant AHJ approval.
Other Options Explained:
Option B (Use of Mall Areas for Exhibits or Displays):
Requires a permit due to potential fire hazards, obstructions to exits, and fire load introduced by exhibits.
Refer to NFPA 1, Chapter 20 for fire safety requirements in malls.
Option C (Storage, Use, and Handling of Flammable Liquids):
AHJ oversight is required as flammable liquids pose significant fire risks.
Refer to NFPA 30 (Flammable and Combustible Liquids Code).
Option D (Installation of an Automatic Fire Suppression System):
Requires a permit to ensure proper installation, design, and compliance with NFPA 13.
Summary:
Routine maintenance of fire protection systems does not require a permit because it involves keeping systems operational rather than introducing new installations, hazards, or modifications.
NEW QUESTION # 41
What is the minimum number of separate and remote means of egress in a new assembly occupancy with an occupant load greater than 1,000?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Egress Requirements for Assembly Occupancies:
According to NFPA 101 (Life Safety Code), Section 12.2.4.1, a new assembly occupancy with an occupant load exceeding 1,000 people requires a minimum of 4 separate and remote means of egress.
Why Four Egress Routes Are Required:
Larger occupant loads increase the risk of congestion during an evacuation.
Multiple egress routes ensure occupants can safely evacuate without crowding or delays.
Other Options Explained:
Option A (1), Option B (2), and Option C (3):
These options do not meet the requirements for occupant loads exceeding 1,000 in new assembly occupancies.
Summary:
A new assembly occupancy with an occupant load greater than 1,000 requires a minimum of 4 separate and remote means of egress to ensure safe evacuation.
NEW QUESTION # 42
What is the maximum travel distance to a fire extinguisher with a 20-B rating for an ordinary (moderate) type hazard?
- A. 75 ft (22.86 m)
- B. 100 ft (30.48 m)
- C. 30 ft (9.14 m)
- D. 50 ft (15.25 m)
Answer: D
Explanation:
The travel distance to fire extinguishers for different hazard classifications is governed by NFPA 10, Standard for Portable Fire Extinguishers.
For ordinary (moderate) hazards, such as those involving moderate quantities of flammable liquids or combustibles, the maximum travel distance to a fire extinguisher with a 20-B rating is 50 feet (15.25 meters).
The B rating refers to extinguishers effective against Class B fires, which involve flammable liquids (e.g., oils, gasoline, solvents).
The 50-foot requirement ensures that fire extinguishers are accessible within a reasonable distance to promptly respond to a fire.
30 feet (A) applies to higher hazard levels like kitchens or specific severe risks.
75 feet (C) is more typical for Class A hazards.
100 feet (D) would not meet NFPA 10 standards for moderate hazards involving flammable liquids.
Reference:
NFPA 10, Section 6.2.1.1: Travel distance requirements based on hazard classification.
NEW QUESTION # 43
For flammable and combustible liquids, what is the number of control areas allowed on the 2nd floor above grade level of a building?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
The number of control areas for flammable and combustible liquids is regulated under NFPA 30 and the International Fire Code (IFC). A control area is a designated area within a building where quantities of hazardous materials are allowed to be stored or used.
For the 2nd floor above grade level, the number of control areas is reduced compared to ground level due to increased risks related to fire containment, evacuation, and firefighting operations.
Specifically:
Ground floor: Up to 4 control areas are allowed.
2nd floor above grade: Up to 3 control areas are allowed.
The reduction ensures that hazardous materials are limited as the building height increases, thereby mitigating fire spread and potential risks.
Reference:
NFPA 30, Flammable and Combustible Liquids Code
IFC Table 5003.8.2: Control area limits based on building levels.
NEW QUESTION # 44
What NFPA code or standard would be used to answer an inquiry regarding the minimum required water temperature for a sprinkler system's water storage tanks?
- A. NFPA 72
- B. NFPA 101
- C. NFPA 25
- D. NFPA 13
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Sprinkler System Design and Installation:
NFPA 13 (Standard for the Installation of Sprinkler Systems) provides detailed guidance on the design, installation, and requirements for water storage tanks, including minimum water temperature to prevent freezing in cold climates.
Other Options Explained:
Option B (NFPA 25): Focuses on inspection, testing, and maintenance of systems, not design parameters.
Option C (NFPA 72): Covers fire alarm systems, not sprinkler systems.
Option D (NFPA 101): Addresses life safety issues, not sprinkler system specifics.
Summary:
Use NFPA 13 to determine the minimum required water temperature for sprinkler system storage tanks.
NEW QUESTION # 45
How often shall emergency egress and relocation drills in educational occupancies be conducted?
- A. Weekly
- B. Every semester
- C. Monthly
- D. Annually
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Drill Frequency in Educational Occupancies:
Per NFPA 101 (Life Safety Code), Section 14.7.2, emergency egress and relocation drills in educational occupancies are required to be conducted monthly during the school year.
Purpose of Monthly Drills:
Frequent drills ensure students and staff are familiar with evacuation procedures, improving safety during actual emergencies.
Other Options Explained:
Option A (Weekly): Excessive and not required by NFPA 101.
Option C (Every semester): Insufficient frequency for maintaining readiness.
Option D (Annually): Not frequent enough for educational settings.
Summary:
Emergency egress and relocation drills in educational occupancies must be conducted monthly during the school year.
NEW QUESTION # 46
Fire extinguishers having a gross weight not exceeding 40 lb (18.14 kg) shall be installed to which of the following criteria?
- A. The top of the fire extinguisher is not more than 5 ft. (1.53 m) above the floor
- B. The top of the fire extinguisher is not more than 5 ft. 6 in (1.68 m) above the floor
- C. The bottom of the fire extinguisher is not more than 5 ft. (1.53 m) above the floor
- D. The bottom of the fire extinguisher is not more than 5 ft. 6 in. (1.68 m) above the floor
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Installation Height Requirements for Fire Extinguishers:
According to NFPA 10 (Standard for Portable Fire Extinguishers), Section 6.1.3.8, fire extinguishers with a gross weight not exceeding 40 lb (18.14 kg) must be installed so that the top of the extinguisher is not more than 5 ft. (1.53 m) above the floor.
Why This Height is Important:
A maximum height of 5 feet ensures accessibility to fire extinguishers for most people during emergencies.
Other Options Explained:
Option A (5 ft. 6 in): Exceeds the NFPA 10 limit and is too high for practical use.
Option C and D (Bottom of the extinguisher): NFPA 10 specifies the height based on the top of the extinguisher, not the bottom.
Summary:
Fire extinguishers with a weight not exceeding 40 lb must have their top installed no more than 5 feet (1.53 m) above the floor.
NEW QUESTION # 47
What is the rating for an interior finish material with a flame spread index of 100?
- A. Class B
- B. Class A
- C. Class D
- D. Class C
Answer: A
Explanation:
Interior finish materials are rated based on their flame spread index (FSI), which measures how quickly flames spread across the material's surface. This classification is outlined in NFPA 101, Life Safety Code, Table A.10.2.3.2.
Class A: Flame spread index of 0-25 (lowest flame spread, highest resistance).
Class B: Flame spread index of 26-75 (moderate flame spread).
Class C: Flame spread index of 76-200 (higher flame spread).
Class D: Not defined in NFPA standards (typically exceeds Class C values).
For a flame spread index of 100, the material falls within the Class C range. However, since 100 exceeds the threshold for Class B (75), it is appropriately classified as Class C.
Reference:
NFPA 101, Table A.10.2.3.2: Flame spread classifications for interior finishes.
NEW QUESTION # 48
How much clear space shall be maintained around the circumference of a fire hydrant (except as otherwise required or approved)?
- A. 24 in. (610 mm)
- B. 60 in. (1524 mm)
- C. 36 in. (914 mm)
- D. 48 in. (1219 mm)
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Clear Space Requirements for Fire Hydrants:
According to NFPA 1 (Fire Code), Section 18.5.7.1, a clear space of at least 36 inches (914 mm) must be maintained around the circumference of a fire hydrant.
Why 36 Inches is Required:
Maintaining 36 inches of clear space ensures that fire hydrants are:
Readily accessible for firefighters during emergencies.
Free from obstructions that may hinder operation or connection of hoses.
Other Options Explained:
Option A (24 in): Insufficient clearance; may obstruct hydrant accessibility.
Option C (48 in) and Option D (60 in): More than required; not mandated by NFPA 1.
Summary:
A 36-inch (914 mm) clear space must be maintained around the circumference of a fire hydrant to ensure accessibility and operability.
NEW QUESTION # 49
What is the maximum area allowed for draft stops provided between a suspended ceiling and the floor above?
- A. 3,000 ft² (280 m²)
- B. 1,000 ft² (93 m²)
- C. 500 ft² (46 m²)
- D. 1,500 ft² (140 m²)
Answer: B
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Draft Stops and Fire Protection:
Draft stops are installed to limit the spread of smoke and heat in concealed spaces, such as the area between a suspended ceiling and the floor above.
According to NFPA 13 (Standard for the Installation of Sprinkler Systems), Section 8.15.1.2.4, the maximum area for draft stops is 1,000 ft² (93 m²).
Purpose of Limiting Area:
Limiting the area to 1,000 ft² ensures smoke and fire are contained within smaller sections, slowing the spread and improving fire control by sprinklers.
Other Options Explained:
Option A (500 ft²): Too small; not the maximum allowed under NFPA 13.
Option C (1,500 ft²) and Option D (3,000 ft²): Exceed the allowable area for draft stops.
Summary:
The maximum area allowed for draft stops provided between a suspended ceiling and the floor above is 1,000 ft² (93 m²) per NFPA 13.
NEW QUESTION # 50
What is the minimum frequency for the inspection and testing of fire door assemblies?
- A. Every month
- B. Every 6 months
- C. Every year
- D. Every 2 years
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Fire Door Inspection and Testing:
According to NFPA 80 (Standard for Fire Doors and Other Opening Protectives), Section 5.2.4, fire door assemblies must be inspected and tested at a minimum frequency of once every year.
Purpose of Annual Testing:
Fire door assemblies are critical for compartmentalization and containment during a fire.
Annual inspection ensures that:
Doors close and latch properly.
Seals and hardware are intact.
There are no obstructions preventing their operation.
Other Options Explained:
Option A (Every month): Excessive; NFPA 80 specifies an annual minimum.
Option B (Every 6 months): Not required under NFPA 80.
Option D (Every 2 years): Insufficient to ensure compliance and performance.
Summary:
Fire door assemblies must be inspected and tested annually to meet NFPA 80 requirements.
NEW QUESTION # 51
Prior to seeking system acceptance for a sprinkler installation, an installer shall do which of the following?
I . Perform all required acceptance tests
II . Complete all contractors' material and test certificates
III . Notify the AHJ of the time and date of the test
IV . Complete owners' approval form and forward it to the AHJ
- A. I and IV
- B. III and IV
- C. I, II, and III
- D. II, III, and IV
Answer: C
Explanation:
Before seeking system acceptance for a sprinkler installation, the installer must complete specific steps to comply with NFPA 13, Standard for the Installation of Sprinkler Systems:
Perform all required acceptance tests (I): Ensures the system functions as designed.
Complete contractors' material and test certificates (II): Certifies that the materials and testing meet NFPA standards.
Notify the AHJ (III): Ensures the AHJ can witness the tests and validate compliance.
The owner's approval form (IV) is not an NFPA requirement for acceptance testing.
Reference:
NFPA 13, Chapter 24: Requirements for acceptance testing.
NEW QUESTION # 52
Labels for individual containers, cartons, or packages of hazardous materials require which of the following?
- A. Conspicuous marking or labeling meeting national standards
- B. Marking consistent with the owner's requirements
- C. Unique color coding for all items with a posted key
- D. No special identification
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Labeling Hazardous Materials:
Per NFPA 704 (Standard System for the Identification of the Hazards of Materials for Emergency Response) and OSHA regulations, hazardous materials must have conspicuous marking or labeling that meets recognized national standards.
Purpose of Conspicuous Marking:
Clear identification ensures emergency responders, workers, and occupants can recognize and handle hazardous materials safely.
Other Options Explained:
Option A (No special identification): Incorrect; labeling is mandatory.
Option B (Unique color coding): While color coding is part of the system, it must align with national standards, not a unique system.
Option D (Owner's requirements): Owner-specific markings may not comply with NFPA or OSHA standards.
Summary:
Hazardous material containers must have conspicuous marking or labeling meeting national standards.
NEW QUESTION # 53
On a routine inspection of an automobile repair garage, the inspector notes that there are open containers of paint in and around the garage. Which standard addresses the proper storage, handling, and use of the paint?
- A. NFPA 30
- B. NFPA 10
- C. NFPA 13
- D. NFPA 58
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Storage and Handling of Flammable Liquids:
NFPA 30 (Flammable and Combustible Liquids Code) specifically addresses the storage, handling, and use of flammable and combustible liquids, including paints, in commercial and industrial settings.
Why NFPA 30 Applies:
Paints often have volatile, flammable components that must be stored in compliant containers and cabinets to prevent fire hazards.
Other Options Explained:
Option A (NFPA 58): Focuses on liquefied petroleum gas (LP-Gas).
Option C (NFPA 13): Covers sprinkler systems.
Option D (NFPA 10): Addresses portable fire extinguishers.
Summary:
NFPA 30 governs the proper storage, handling, and use of paint and other flammable liquids.
NEW QUESTION # 54
......
NFPA CFI-I Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
CFI-I PDF Dumps Are Helpful To produce Your Dreams Correct QA's: https://actualtests.vceengine.com/CFI-I-vce-test-engine.html
